NOTE:

Firstly, get the root certificate. Then follow the steps below: Procedures: Double click the certificate file (with '.cer' extension) Choose 'System' from the keychain option.Then press 'OK'When the following window pops-up, click the 'Always Trust' button.Then you. ROOT is available on Linux, Mac, and (as a beta release) on Windows. The latest stable ROOT release is 6.22/02 (about ROOT versioning scheme). There are several ways to install ROOT on your computer: they are all listed in the table of content on the right. Which one is best for you depends on your operating system and usage requirements.

Manually installing root certificate on Mac OSX. NOTE: The following is based on OSX Yosemite 10.10.5. Other OS versions will have similar settings but they may not be worded the same or may be in slightly different places. Login to the web admin and click the Download Root Certificate button under Apps SSL Inspector Settings. If the installation is successful, you'll be presented with a 'The installation was successful' message with the executable window. To verify that the 2034 SSL Certificate has been installed successfully, you can navigate to ' Keychain Access' and look within the 'System Keychain' Folder for Securly SSL Certificate. Right-click the file and select Install Certificate. You might be prompted for admin credentials and/or a confirmation prompt. On the first wizard screen, click Next. On the Certificate Store screen: Select the Place all certificates in the following store option. Select the Trusted Root Certification Authorities option.

Between mid October 2019 and mid February 2020 everyone in the Army was migrated to use their PIV Authentication certificate for Email access. You no longer use the Email certificate for Enterprise Email or any CAC enabled websites

Mac users who choose to upgrade (or already have upgraded) to Mac OS Catalina (10.15.x) will need to uninstall all 3rd Party CAC enablers per https://militarycac.com/macuninstall.htm AND reenable the built in smart card ability (very bottom of macuninstall link above)

If you purchased your Mac with OS Catalina (10.15.x) already installed, you can skip the uninstall part above and follow the instructions below.

6 'high level' steps needed, follow down the page to make this a painless systematic process

1.	Is your CAC reader 'Mac friendly'?
2.	Can your Mac 'see' the reader?
3.	Verify which version of Mac OS you have
4.	Figure out which CAC (ID card) you have
5.	Install the DoD certificates
5a.	Additional DoD certificate installation instructions for Firefox users
6.	Decide which CAC enabler you want to use (except for 10.12-.15)

Step 1: Is your CAC reader Mac friendly?

Visit the USB Readers page to verify the CAC reader you have is Mac friendly.

Visit the USB-C Readers page to verify the CAC reader you have is Mac friendly.

'Some, not all' CAC readers may need to have a driver installed to make it work.

NOTE: Readers such as: SCR-331 & SCR-3500A may need a firmware update (NO OTHER Readers need firmware updates).

Information about these specific readers are in Step 2

Step 2: Can your Mac 'see' the reader?

Plug the CAC reader into an open USB port before proceeding, give it a few moments to install

Step 2a: Click the Apple Icon in the upper left corner of the desktop, select 'About This Mac'

Step 2b: Click 'System Report...' (button)

Step 2c: Verify the CAC reader shows in Hardware, USB, under USB Device Tree. Different readers will show differently, most readers have no problem in this step. See Step 2c1 for specific reader issues.

Step 2c1: Verify firmware version on your SCR-331 or GSR-202, 202V, 203 CAC, or SCR-3500a reader. If you have a reader other than these 5, Proceed directly to step 3

Step 2c1a-SCR-331 reader

If your reader does not look like this, go to the next step.

In the 'Hardware' drop down, click 'USB.' On the right side of the screen under 'USB Device Tree' the window will display all hardware plugged into the USB ports on your Mac. Look for “SCRx31 USB Smart Card Reader.” If the Smart Card reader is present, look at 'Version' in the lower right corner of this box: If you have a number below 5.25, you need to update your firmware to 5.25. If you are already at 5.25, your reader is installed on your system, and no further hardware changes are required. You can now Quit System Profiler and continue to Step 3.

Step 2c1b-SCR-3500A reader

If you have the SCR3500A P/N:905430-1 CAC reader,you may need to install this driver, as the one that installs automatically will not work on most Macs. Hold the control key [on your keyboard] when clicking the .pkg file [with your mouse], select [the word] Open

Step 3: Verify which version of MacOS do you have?

(You need to know this information for step 6)

Step 3a: Click the Apple Icon in the upper left corner of your desktop and select 'About This Mac'

Step 3b: Look below Mac OS X for: Example: Version 10.X.X.

Step 4: Figure out which CAC (ID Card) you have

(You need to know this information for step 6)

Look at the top back of your ID card for these card types. If you have any version other than the six shown below, you need to visit an ID card office and have it replaced. All CACs [other than these six] were supposed to be replaced prior to 1 October 2012.

Find out how to flip card over video

Step 5: Install the DoD certificates (for Safari and Chrome Users)

Go to Keychain Access

Click: Go (top of screen), Utilities, double click Keychain Access.app

(You can also type: keychain access using Spotlight (this is my preferred method))

Select login (under Keychains),and All Items (under Category).